廠家供應海綿泡沫塑料落球回彈試驗儀
產品概述
產品名稱:海綿泡沫塑料落球回彈儀-(液晶顯示)
型號:HMLQ-500
一、制造標準:
(GB/T6670-2008 ISO8307 ASTM D3574 ISO8307)軟質泡沫聚合材料落球法回彈性能的測定
二、適用范圍及功能:
適用于測定軟質聚氨酯泡沫塑料的落球式回彈性能.落球回彈是通過給定直徑和質量的鋼球在規定高度上自由落在泡沫塑料試樣上,計算鋼球回彈的zui大高度與鋼球落下高度比值的百分率既回彈率,以回彈率表示泡沫塑料的回彈性能。滿足08標準A法和B法試驗方法。主要是測試塑料泡沫材料及海綿材料的回彈性能。 落球回彈測量精度高采用微處理器進行控制,中文顯示,并可打印試驗數據。
三、技術參數:
1、鋼球回落高度: 460mm(國標)
500mm(美標)
2、鋼球直徑: ¢16mm
3、落球回彈率精度: <1%
4、被測試樣尺寸: 長*寬*高=100 mm×100 mm×100(50)mm
5、自動計算平均回彈高度
6、自動計算平均回彈率
四、主要配置:
1、試驗主機一臺
2、智能液晶控制操作系統一臺
3、鋼球釋放機構兩套(手動釋放機構1套、自動釋放機構1套)
4、鋼球捕捉機構一套
5、高度調節機構一組
6、精密光電傳感器一套
7、鋼球4個
8、微型打印機一臺
9、水平校準機構一組
五、試驗步驟:
將調節后的試樣水平置于回彈儀的測試位置上,通過調節使鋼球底部從固定位置到泡沫塑料表面的落下高度為460mm。在釋放裝置上固定鋼球,然后使鋼球自由落下。對每一個試樣做三次回彈,取三次回彈中的zui大值。每次回彈鋼球應落在試樣表面的同一位置上,并且兩次回彈的時間間隔應控制在20s之內。如果鋼球在回彈過程中碰到或彈出測量裝置,所得數據無效,需重新補做。
Product Name: sponge foam ball rebound tester - (liquid crystal display)
型號:HMLQ-500
Model: HMLQ-500
一、制造標準:
A, manufacturing standards:
(GB/T6670-2008 ISO8307 ASTM D3574 ISO8307)軟質泡沫聚合材料落球法回彈性能的測定
(GB/T6670-2008 ISO8307 ASTM D3574 ISO8307) determination method of falling ball rebound performance soft foam polymerization
二、適用范圍及功能:
Two, applicable scope and functions:
適用于測定軟質聚氨酯泡沫塑料的落球式回彈性能.落球回彈是通過給定直徑和質量的鋼球在規定高度上自由落在泡沫塑料試樣上,計算鋼球回彈的zui大高度與鋼球落下高度比值的百分率既回彈率,以回彈率表示泡沫塑料的回彈性能。滿足08標準A法和B法試驗方法。主要是測試塑料泡沫材料及海綿材料的回彈性能。 落球回彈測量精度高采用微處理器進行控制,中文顯示,并可打印試驗數據。
Suitable for performance ball rebound fell determination of soft polyurethane foam. Ball rebound is given by steel ball diameter and quality in the specified height of free fall on the foam specimen, the maximum height calculation of ball rebound the ball falling height and the percentage of both resilience, said resilient properties of foam to rebound rate. To meet the 08 Standard Test Method A method and B method. Mainly rebound performance test of plastic foam material and the sponge material. Ball rebound high measurement precision by using microprocessor to control, Chinese display, and print the test data.
三、技術參數:
Three, technical parameters:
1、鋼球回落高度: 460mm(國標)
1, the ball drop height: 460mm (GB)
500mm(美標)
500mm (American Standard)
2、鋼球直徑: ¢16mm
2, the diameter of the steel ball: Phi 16mm
3、落球回彈率精度: <1%
3, falling ball rebound rate of accuracy: 1% <
4、被測試樣尺寸: 長*寬*高=100 mm×100 mm×100(50)mm
4, the test sample size: length * width * height =100 mm × 100 mm × 100 (50) mm
5、自動計算平均回彈高度
5, automatic calculation of average rebound height
6、自動計算平均回彈率
6, automatic calculation of average rate of rebound
四、主要配置:
Four, the main configuration:
1、試驗主機一臺
1, test a host
2、智能液晶控制操作系統一臺
2, inligent LCD control operating system a
3、鋼球釋放機構兩套(手動釋放機構1套、自動釋放機構1套)
3, two sets of ball release mechanism (manual release mechanism of 1 sets, 1 sets of automatic release mechanism)
4、鋼球捕捉機構一套
4, a steel ball catching mechanism
5、高度調節機構一組
5, the height adjusting mechanism of a group
6、精密光電傳感器一套
6, a set of precision photoelectric sensor
7、鋼球4個
7, ball 4
8、微型打印機一臺
8, a miniature printer
9、水平校準機構一組
9, a group of horizontal alignment mechanism
五、試驗步驟:
Five, the test procedure:
將調節后的試樣水平置于回彈儀的測試位置上,通過調節使鋼球底部從固定位置到泡沫塑料表面的落下高度為460mm。在釋放裝置上固定鋼球,然后使鋼球自由落下。對每一個試樣做三次回彈,取三次回彈中的zui大值。每次回彈鋼球應落在試樣表面的同一位置上,并且兩次回彈的時間間隔應控制在20s之內。如果鋼球在回彈過程中碰到或彈出測量裝置,所得數據無效,需重新補做。
Will test the position of the sample placed horizontally on the rebound instrument adjusted by adjusting the ball on the bottom, from a fixed position to the foam surface fall height of 460mm. Fixed ball in releasing device, and then the ball free fall. Do three rebound on every sample, a maximum value of three rebound. Each time the rebound ball should be in the same position on the sample surface, and the two rebound time interval should be controlled within 20s. If the ball on the rebound process encountered or pop-up measuring device, the data is invalid, need to do.
- 上一個: 體積電阻率測試儀(固體液體)
- 下一個: 海綿泡沫疲勞壓陷測試儀(生產商)